ADE-XA USB 2.0 fast ethernet

USB 2.0 Ethernet 10/100 adapter with support for all current OSs.

Input USB 2.0
Output Ethernet
rate 10/100 Mbit/s
PC connection USB type A-M, permanently connected cable, cable 10 cm
Extra Wake on LAN

Where to buy

The compact AXAGON ADE-XA adapter easily converts the USB 2.0 port to the Fast Ethernet 10/100 Mbit port.

Besides wide compatibility, the network card offers also advanced features including IPv4/IPv6 checksum engine to reduce CPU loading by checksums, crossover detection and autocorrection, or support for various Wake-on-LAN modes.

Thanks to its simple installation, the USB - Ethernet adapter easily extends your computer by the missing RJ-45 network connector, adds another network card or replaces the original defunct network connection.

The support for all current versions of Windows, MacOS, Linux, and Android operating systems allows it to be used for nearly any desktop, laptop or ultrabook, and even some tablets.

• USB 2.0 interface, backward compatible with USB 1.1.
• Supports transmission rates 1.5 / 12 / 480 Mbit/s (low / full / high speed).
• Connecting USB 2.0 port with Type A male connector on an 8 cm long cable permanently attached to the adapter.

• Ethernet interface with RJ-45 connector for UTP or STP cable connection.
• Supported transmission rates for the Ethernet interface 10/100 Mb/s.
• Supported IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX specifications.
• 10/100 Mbit/s autodetection.
• Supports IPv4 / IPv6 packet Checksum Offload Engine (COE) to reduce processor load, including IPv4 IP/TCP/UDP/ICMP/ IGMP
& IPv6 TCP/UDP/ICMPv6 checksum control and generation.
• Supports IEEE 802.1Q VLAN tagging
& 2 VLAN ID filtering.
• Supports full-duplex transmissions with IEEE 802.3x flow control and half-duplex transmissions with back-pressure flow control.
• Supports Auto MDI/MDIX - crossover detection and auto-correction eliminates the need for crossover cables.

Other features:
• Full Plug and Play and Hot Plug support.
• Adapter power supply via USB (bus power) - no auxiliary power supply required.
• Two LEDs for indicating activity, network connection and power supply.
• Dimensions 60 x 20 x 19 mm, USB cable length 8 cm, weight incl. USB cable 20 g.
• ASIX AX88772B chipset is used.

Wake-on-LAN feature and advanced Power Management features:
• Supports sleep mode and remote wake up via Magic packet, Microsoft Wakeup Frame, and Link Status Change.
• Supports Power Management offload (ARP
& NS).
• Supports dynamic power management to reduce losses during standby or light traffic on the network.

Supported OSs:
• MS Windows XP / Vista / 7 / 8 / 8.1 / 10 and later, Windows Server 2003 / 2008 / 2012 / 2016 and later (supported are all 32 and 64-bit versions of Windows OSs), MacOS X 10.5 and higher, Linux with kernel 2.6.14 and above, Windows CE 7.0, Android all versions (WARNING - check with the Android device manufacturer if the Ethernet connection is supported).

Package contains:
• USB - Ethernet adapter with an 8 cm long permanently attached cable,
• printed installation guide in English, Czech, Slovak and Polish,
• packed in a blister with a sealed-on back card.

interface USB 2.0 / USB 1.1
rate 480 / 12 / 1.5 Mbit/s (high / full / low speed)
connector USB Type A male on the cable
cable 8 cm, permanently connected
interface Ethernet
rate 10/100 Mbit/s
connector RJ-45
compatibility IEEE 802.3u 100Base-TX
compatibility IEEE 802.3 10Base-T
Supported features
Virtual LAN yes (IEEE 802.1Q VLAN tagging & 2 VLAN ID filtering)
Wake on LAN yes (incl. AMD Magic Packet, Microsoft Wake-up frame)
Plug and Play yes
Hot Plug yes
Other features
indication red LED - connection to the power supply (permanently on)
indication blue LED - connection to the network (permanently on), data transmission (flashes)
chipset ASIX AX88772B
dimensions 60 x 20 x 19 mm
weight 20 g (incl. USB cable)
Power supply
on the bus yes (USB bus power)
OS support
MS Windows 10 / 8.1 / 8 / 7 / Vista / XP (all 32- and 64-bit versions)
MS Windows Server 2016 / 2012 / 2008 / 2003 (all 32- and 64-bit versions)
Mac OS X 10.5 and higher
Linux kernel 2.6.14 and higher
Android all versions ( ! - verify support at the Android device manufacturer)

Package contents

- USB - Ethernet adapter
- installation guide


- printed installation manual in English, Czech, Slovak and Polish

Product package

- blister with a sealed-on paper back card
- package dimensions 14.3 x 2.6 x 12.2 cm
- weight of 1 pc package 54 g
- EAN 8595247902870

Export package

- number of pieces in the box: 80
- total weight of the box: 5.9 kg G.W.
- box dimensions: 44 x 34 x 29 cm


A): If the network card is not displayed in "Device Manager", a USB port (or a PCIe slot in the event of an internal network card) may be malfunctioning.

B): Try plugging the network card into another USB port (or another PCIe slot on the PC motherboard in the event of an internal network card, or temporarily disconnect all other PCIe cards). The network card should be detected and you should be prompted to install the drivers. If the problem persists, plug the network card into the USB port (PCIe slot) of another computer to verify its functionality.

A): If this happens, it means that the operating system failed to get the necessary information to install the drivers.

B): The cause may be a defective USB extension cable or damaged device. If the problem persists, plug the network card into the USB port of another computer to verify its functionality.

A): Before connecting the USB network card to an Android device (tablet), you first need to verify with the device manufacturer whether the device supports the Ethernet network feature and also whether the USB network card drivers are included in your specific ANDROID ROM installation.

B): Use a USB connector with OTG support to connect the USB network card to your tablet. If the device (tablet) is equipped with a Mini USB or Micro USB connector, use an OTG reduction or cable to connect it.

A): The Ethernet interface transmission speed setting is a fully independent from USB connection and can be set in the network card's properties. The default setting is an automatic negotiation when the speed is set according to other elements in the LAN network.

B): If you connect the Gigabit adapter via the USB 2.0 port, the overall bandwidth of the adapter will be limited by bandwidth of the USB 2.0 interface, which is theoretically 480 Mb/s; in Gigabit Ethernet environments this adapter will be up to 4x faster than 10/100 Ethernet adapters.

The problem probably is that you did not allow the „installation of application from an unidentified developer“ from "Security & Privacy" application during installation the driver.
Please check "Security
& Privacy" application if there is possible to allow the „installation of application from an unidentified developer“.  If this option is no longer available, you need to proceed as follows:

- Close the "Security & Privacy" window - IMPORTANT !!!
- uninstall the driver using the "AX88772C_772B_772A_760_772_Uninstall_v140.command" file from   the folder with the driver
- during the uninstallation the „application is from an unidentified developer“ message appears – left this window OPEN !!!
- open "Security
& Privacy" again and allow „installation of application from an unidentified developer“  - you will need an administrator password
- Close the "Security
& Privacy" window via OK button.
- Continue and finish uninstallation of the driver
- Restart the computer and then reinstall the driver

Because you have already allowed „installation of application from an unidentified developer“, the message should not be displayed again.
If it appears, do not close it, and allow „installation of application from an unidentified developer“ in "Security
& Privacy".

User Manual



Technical support inquiry

We provide technical support only in Czech and English. Thank you for your understanding.