PCEU-430VL PCIe controller 4x external SuperSpeed USB
PCI-Express card with four external USB 3.2 Gen1 ports.
|Output||USB 3.2 Gen 1, UASP, 4-port output|
|rate||up to 5 Gbit/s|
|PC connection||x1 Slot|
|Power supply||from a PC source|
Where to buy
AXAGON PCEU-430VL PCI-Express card adds four external high speed USB 3.2 Gen 1 ports to your desktop computer.
All four SuperSpeed USB ports are taken out to the bracket. Reliable card power from PC power supply via SATA power connector.
The USB controller is equipped with a renowned VIA Labs company chipset with proven seamless compatibility and UASP support.
• PCI-Express 2.0 interface, compatible with PCI-Express 1.0a / 1.1 / 2.1 / 3.0.
• Number of lines: (x1), compatible with x1 / x4 / x8 / x16 PCIe slots.
• A bandwidth of 1-Lane PCI-Express 2.0 bus is 5 Gb/s.
• 4x external USB 3.2 Gen 1 port with USB type A-F connectors.
• SuperSpeed USB - USB 3.2 Gen 1 interface (before USB 3.1 Gen 1 / USB 3.0).
• Compatible with USB 3.2 Gen 2, backward compatible with USB 2.0 a USB 1.1.
• Supports transmission rates 5000 / 480 / 12 / 1.5 Mb/s (super / high / full / low speed).
• When connected to a PCI-Express bus version 1.0, theor. transmission rate max. 2500 Mb/s.
• Full Plug and Play support.
• Supports concurrent activity of SuperSpeed USB, USB 2.0 and USB 1.1 devices.
• Compliant with the final official xHCI specification revision 1.0 by USB-IF.
• Supports UASP (USB Attached SCSI) for faster data transmission in Windows 8 and later.
• Fully supports Hot Plug connecting and disconnecting of USB devices while running.
• Internal SATA power connector to powering the controller from a PC power supply.
• VIA Labs VL805 chipset is used.
Supported operating systems:
• MS Windows XP / Vista / 7 / 8 / 8.1 / 10, Windows Server 2003 / 2008 / 2012 / 2016 (supported are all 32- and 64-bit Windows OS versions), Linux with kernel 2.6.31 and above.
• Note: Drivers are only installed for Windows XP / Vista / 7. For Linux, Windows 8 / 8.1 / 10, Server 2012 / 2016 and later versions, no external drivers are required, they are already part of the operating system.
• PCI-Express controller with a standard bracket,
• multilingual guide CZ/DE/DK/ENG/ESP/FIN/FR/GR/HR/HU/IT/NL/PL/PT/RO/RU/SK/SWE/TR/BG/CN/ARA,
• packed in a cardboard box.
|number of lines||1-Lane (x1)|
|compatibility||PCI-Express 1.0a / 1.1 / 2.0 / 2.1 / 3.0|
|compatibility||x1 / x4 / x8 / x16 PCIe slot|
|interface||USB 3.2 Gen 1 / USB 3.0 / USB 2.0 / USB 1.1|
|rate||5000 / 480 / 12 / 1.5 Mbit/s (super / high / full / low speed)|
|number of ports||4|
|connector||4x USB Type A female|
|total permeability||5 Gbit/s theoretically (give by PCIe 2.0 1-Lane input)|
|UASP||yes (Win 8 and higher)|
|automatic installation||yes (from Win 8 and Server 2012)|
|Plug and Play||yes|
|chipset||VIA Labs VL805|
|from a PC source||15pin power SATA|
|MS Windows||10 / 8.1 / 8 / 7 / Vista / XP (all 32- and 64-bit versions)|
|MS Windows Server||2016 / 2012 / 2008 / 2003 (all 32- and 64-bit versions)|
|Linux||kernel 2.6.31 and higher|
- printed multilingual manual CZ/DE/DK/ENG/ESP/FIN/FR/GR/HR/HU/IT/NL/PL/PT/RO/RU/SK/SWE/TR/BG/CN/ARA
- cardboard box
- package dimensions 14.5 x 11 x 2.8 cm
- weight of 1 pc package 77 g
- EAN 8595247904478
- number of pieces in the box: 100
- total weight of the box: 7.75 kg G.W.
- box dimensions: 58 x 32 x 29 cm
A): If the PC does not run with the card or the card is mistakenly detected in “Device Manager”, or if there is a yellow exclamation mark on the driver, or if “Device Manager” reports an error code “Code 10 - The device cannot start”, the card is in conflict with another device in your computer.
B): In most cases, this conflict can be solved by moving the card to another PCI (PCIe) slot, with the BIOS assigning other free resources to the card. If the move does not help, try the card separately, with no additional cards inserted. If the card cannot be moved to another slot, you can reset the BIOS of the computer (by jumper on the board or pulling out the backup battery, we recommend that you note all the original settings and reset everything to the required values). This will cause the IRQ, DMA, and I/O resources to be redistributed.
A): If the copy speed is approximately 35 MB/s, it means that the connection between the controller and the connected device is working only in the USB 2.0 mode. Some types of USB 3.0 devices may have a problem with proper detection.
B): Make sure that the connected device is USB 3.0 compatible. Please check if an additional power supply to the controller is connected (the power reduction is not included, the card is powered by a standard power connector that is part of each source; we recommend avoiding Molex connectors and splitters that often cause problems). The error could be caused by, for example, the old firmware of the device you want to connect, some manufacturers provide a new firmware to their products, which could solve this situation. Alternatively, try replacing the USB 3.0 cable that may be damaged. When testing, do not use USB 3.0 extensions that could also cause this problem.
A): Booting from an additional USB card is not possible because each card has a different chip. The BIOS of the motherboard does not contain information that will allow to "see" the connected USB device. Detection of attached devices occurs only after the additional card drivers have been booted when the operating system starts running.
B): When using the integrated USB from the motherboard, of course, the BIOS is programmed to include information about the chip of the controller used for USB on the motherboard. Therefore, the motherboard BIOS "sees" the connected USB device and therefore can boot from it.
A): Please check your BIOS settings. Power Management Setup – Wake Up Event Setup – Resume by PCI-E Device (individual items may vary by MB type) should be set to disabled.
B): If this does not help, try updating your motherboard BIOS and check the ACPI item when still in the BIOS If not even this helps, move the controller card to another PCIe slot (may also be x16 - slots differ only in the number of lines). It is possible that the card is in conflict with another device on your computer. For some types of BIOS, you can do this directly by enabling Force Update ESCD (Reset Configuration Data etc.) in the PnP & PCI Configurations menu. This will cause the IRQ, DMA, and I/O resources to be redistributed.
A): The VBScript is incorrectly registered in your Windows installation.
B): To fix the problem and download the patch go to Microsoft site: https://blogs.technet.microsoft.com/fixit4me/2009/01/30/register-windows-script-engine-fix-it-live/